- Komplete audio 6 vs scarlett 2i2 how to#
- Komplete audio 6 vs scarlett 2i2 drivers#
- Komplete audio 6 vs scarlett 2i2 series#
We started with some guitar tracks, recording with the “Inst” function activated. In all, it took us about 20 minutes to be in a position to start using the interface – your time may vary depending on the speed of your internet connection.
Komplete audio 6 vs scarlett 2i2 drivers#
After getting plugged in to the computer (we were using a MacBook Pro), it immediately prompted us to visit the Focusrite website to download the appropriate drivers and software to run it. We loved how easy it was to get started with the 2i2. This unit also has 48v phantom power, activated by a switch on the front of the unit, so there’s no need for separate power for your condenser mics. If you have someone recording while you mix, you can simultaneously output to headphones, and make use of the individual headphone monitor volume control. There are individual gain controls for both channels, and simple controls to switch between direct monitoring and having sound come through the computer. It works wonders for adding detail and clarity to vocal tracks, and is a welcome feature on this new edition. The function of this control is to increase the mid-high frequencies in the vocals that are often missing from inexpensive and budget microphones.
The “ Air” button is designed to be used for vocals when a mic is plugged in by XLR. This feature was added in response to the extreme clipping that older generations famously suffered from. By activating the “Inst” button, you’re letting the unit know that it’s receiving a guitar or bass signal generated by magnetic pickups, it will respond by optimizing the input gain and impedance to prevent input signal distortion. Next to each input there are 2 buttons labeled “Inst” and “Air”. The 2i2 has 2 input channels, both which can be used for either instrument or microphone (XLR) in. This is probably because the buttons on the 3 rd Gen have been finished in a lovely matte black color, which does a good job of camouflaging them. The control panel somehow manages to look less cluttered than the outgoing model, while gaining extra buttons. It looks great on the desktop, and that’s key in a home setup. It comes finished in the classic Focusrite red aluminum housing, a touch that we really like. If the sound is weak, with only high frequencies, then pin 3 needs to be tied to pin 1 (ground).Externally, there’s not a lot to the 2i2. If they don't then the safest is to leave pin 3 (jack ring) floating, and if that works, then great.
Komplete audio 6 vs scarlett 2i2 how to#
In many cases, the manual will tell you how to unbalance the output. In summary, it's impossible to know what's the right way unless you know what sort of output you have. If the output isn't differential, just impedance balanced, then shorting pin 3 (jack ring) to ground should be fine assuming the sensible case that it's pin 2 that actually carries the signal.
Komplete audio 6 vs scarlett 2i2 series#
Usually each opamp has a series resistor to protect the output against just such an occurrence, but that raises the output impedance from essentially zero ohms to 75-100 ohms so sometimes isn't done. with an opamp on each leg, then it's not OK as one leg will be shorted to ground. If the output is just plain electronically balanced, i.e. not ground referenced, so shorting pin 3 (jack ring) to ground is fine. If the output is electronically servoed, then it's effectively 'fully floating' i.e. However, most outputs these days are not transformer balanced, but use electronics. Pin 3 needs to be left unconnected in this case. If centre-tapped transformer balanced that's not fine at all as half the transformer gets shorted out.
If fully floating transformer balanced, that perfectly fine. Unbalancing a balanced differential output by shorting XLR pin3 (jack ring) to ground is fine or not, depending on the type of balanced output. This is the connection that isn't connected to an active op-amp rather just resistance coupled. One will read a moderately low and fixed unchanging resistance. One will read a rather high and possibly fluctuating resistance. With power off using a TSR cable check resistance between the sleeve to the tip and the ring. I don't know about the gen 3 Scarletts, but earlier generations were impedance balanced and shouldn't be bothered with pin 3 grounded. My apologies if this has been covered as I didn't read all 7 pages.
0 kommentar(er)
